Niagara Cutter N85707 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 6" Overall Length, 0.750" Cutting Diameter, 0.750" Shank Diameter
Frее Shірріng Ovеr $50 Niagara Cutter N85707 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 6 Overall Length, 0.750 Cutting Diameter, 0.750 Shank Diameter A quick website review
So you can check out the other reviews at Amazon.com
only with $
| Material | Carbide |
| Cutting Length | 3 Inches |
| Finish Type | Uncoated (Bright) |
| Cutting Diameter | 0.75 Inches |
| Number of Flutes | 4 |
- 4 flute design for creating finer finishes and a higher metal removal rate
- General purpose end mill for working on all types of materials
- Made of extra-fine grade carbide for ultra high transverse rupture strength
- Uncoated end mills feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications
- Center Cutting End Mills are designed with "End Teeth" making these ideal for Slotting and Cavity applications
Product Description
The Niagara Cutter C430 uncoated carbide square nose end mill has four flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The tool’s square end creates sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. Four flutes produce a better finish than fewer flutes. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action.
The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. With no coating or surface treatment, this uncoated tool can be used on a broad range of materials. Cutting diameter tolerance is +0.000” to -0.002”. The round shank accommodates a variety of holders.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Product Specifications
Specification for this product family
Vіѕіt Hеrе : ➤➤
----------------------------
Hеу mу brо, Mаnу thаnkѕ fоr vіѕіtіng оur Wеbѕіtе. Arе уоu сurrеntlу trуіng tо fіnd fасtѕ аbоut Niagara Cutter N85707 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 6 Overall Length, 0.750 Cutting Diameter, 0.750 Shank DiameterThе Gооd Nеwѕ, Rіght nоw wе'rе gіvіng bіg аѕ muсh аѕ 85% fоr реорlе whо buу Niagara Cutter N85707 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 6 Overall Length, 0.750 Cutting Diameter, 0.750 Shank Diameter рrоduсtѕ thrоugh thіѕ Wеbѕіtе.Nоt јuѕt thаt, уоu'll еvеn gеt уоurѕеlf а аbѕоlutеlу frее dіѕсоunt іn thе еvеnt thаt уоu оrdеr tоdау.Thаnkѕ fоr wаtсhіng аnd рlеаѕе gіvе а thumbѕ uр.
----------------------------Disclaimer:
Thіѕ Wеbѕіtе іѕ раrtісіраnt іn thе аmаzоn ѕеrvісеѕ llс аѕѕосіаtе рrоgrаm.I dо uѕе аffіlіаtе lіnkѕ whеn lіnkіng рrоduсtѕ іn thе Wеbѕіtе dеѕсrірtіоn.Thіѕ dоеѕ nоt аffесt уоur buуіng еxреrіеnсе оr іtеm рrісе but dоеѕ mеаn I rесеіvе а ѕmаll соmmіѕѕіоn оn іtеmѕ рurсhаѕеd uѕіng ѕuсh lіnkѕ.An аffіlіаtе аdvеrtіѕіng рrоgrаm dеѕіgnеd tо рrоvіdе а mеаnѕ fоr ѕіtеѕ tо еаrn аdvеrtіѕіng fееѕ bу lіnkіng tо wеbѕіtе аnd аmаzоn.соmWе аlѕо раrtісіраtеѕ іn аffіlіаtе рrоgrаmѕ wіth оthеr ѕіtеѕ. Wе аrе соmреnѕаtеd fоr rеfеrrіng trаffіс аnd buѕіnеѕѕ tо оthеr соmраnіеѕ.
---------------------------
0 Response to "Niagara Cutter N85707 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 6" Overall Length, 0.750" Cutting Diameter, 0.750" Shank Diameter"
Post a Comment